Gas line work belongs in a narrow category of plumbing tasks where there is no acceptable shortcut. A fitting that isn't fully threaded, a connector that was bent during installation, or a repair that skips the post-work manometer pressure test can produce a leak that's invisible and odorless until conditions for ignition are met. Masters Plumbing Service's certified gas plumbers in Hurst, TX use combustible gas detectors at every connection point after every repair β and every job ends with a documented manometer pressure test before gas is restored to any line we've worked on.
π Call +1-855-718-1500 β Certified Gas Plumbers
These aren't marketing points β they're the minimum requirements for safe gas line work. Every Masters Plumbing Service gas job in Hurst, TX meets all four, on every call, without exception.
No unlicensed person touches gas line work at Masters Plumbing Service. The stakes are too high for on-the-job learning.
After any gas line repair, installation, or reconnection, we pass a calibrated combustible gas detector β sensitive to natural gas and propane at concentrations far below the lower explosive limit β over every fitting, joint, and appliance connection we worked on. A clean detector pass at every point is required before the job is closed out.
This documentation is required by many local inspections and is the professional standard for confirming gas work is complete. Soapy water bubble testing is not an acceptable substitute for a manometer test on anything more than a simple appliance flex connector.
Gas line work β new runs, repairs to service lines, appliance connection upgrades β requires a permit and inspection in most TX jurisdictions. We pull the required permit, schedule the inspection, and provide you with the inspection sign-off as part of the job documentation.
Every job follows the same detection and pressure-testing standard regardless of scope.
Once the utility has confirmed the street supply is shut and the structure has ventilated, we locate the leak, make the repair, detector-test every connection, perform the manometer pressure test, and coordinate with the utility for gas restoration.
Flexible corrugated stainless steel tubing (CSST) connections require proper bonding in most TX jurisdictions to prevent damage from nearby lightning events β a code requirement many contractors overlook. Our gas techs are CSST-bonding trained.
We calculate BTU load for the intended appliances, size the new line in black iron or CSST per the installation context, install at the required depth for buried runs, and perform pressure testing on the new segment before any appliances are connected.
We pressure-test the full distribution system or individual branches per client request, provide a written test result, and report any pressure drop with our best assessment of where the loss is occurring.
Corrugated stainless steel tubing (CSST) is the flexible gas piping used in most newer Hurst homes β it's faster to install than rigid black iron and routes easily through framing. However, CSST requires specific installation requirements: proper fittings, correct bonding to the electrical grounding system, and protection at penetration points to prevent abrasion damage.
{Propane systems used in areas of Hurst, TX without natural gas service have specific considerations compared to natural gas: different line pressures at the regulator (propane distribution pressure varies by system design), different BTU content per cubic foot, and propane's behavior of settling low (it's heavier than air, so propane accumulates at floor level rather than rising to ceilings).|We service propane supply lines from the tank to the structure, appliance connections, regulator function checks, and leak detection using detectors calibrated for propane's lower explosive limit.}
Gas line work follows a defined protocol β no steps skipped, no "close enough." Here's exactly how a Masters Plumbing Service gas call runs from your first contact to a documented, pressure-tested result.
Active gas smell: stay out of the building, call your utility to shut street supply, then call us. Non-emergency gas work (new runs, appliance connections, pressure testing): call to schedule β we confirm certification documentation and permit requirements for your specific job scope before arrival.
On arrival, we conduct a detector survey of the full accessible gas system β not just the suspected area. This establishes a baseline and catches any pre-existing issues beyond the immediate call scope.
For leak repairs, the gas remains off on the affected line until the repair is complete, the detector passes every joint, and the manometer test confirms a leak-free system.
After every gas job β repair, new run, or appliance connection β we conduct a timed manometer pressure hold test on the affected segment and detector-test every connection point. You receive the written test result as part of your job documentation.

Needed a new gas line run to an outdoor kitchen setup. Masters Plumbing Service sized the line correctly for the combined BTU load of the burners and the side burner, ran 3/4-inch black iron through the crawl space and up through the exterior wall, installed a shutoff at the outlet, pressure tested the new segment, and handled the permit and inspection scheduling. Inspection passed first time.
Had three contractors look at moving a gas range β two said they couldn't do it because of the CSST in the line. Masters Plumbing Service's tech was CSST-qualified, relocated the range connection with the correct CSST fittings, added the required bonding conductor to the grounding system, and pressure tested the modified segment. Permit closed with no issues. Very professional from start to finish.
Called Masters Plumbing Service for a propane system inspection before buying a rural property. Their tech checked the regulator function, distribution line pressure, tank connection, and all appliance flex connectors. Found one connector that was beyond its rated service life and replaced it. Written pressure test documentation and a clear condition report on the full propane system.

Masters Plumbing Service dispatches certified gas plumbers throughout Hurst and the broader Hurst, TX service area. Emergency gas response is available around the clock β non-emergency work is scheduled with permit lead time in mind.

Gas line work done right means certified technicians, combustible gas detection at every connection, and a manometer pressure test before gas is restored. Masters Plumbing Service delivers all three on every gas call in Hurst, TX β emergency or scheduled.
π Call +1-855-718-1500 Now